On additives, morphological evolution and dielectric breakdown in low density polyethylene

A series of low density polyethylene systems has been studied with respect to structural evolution and short-term dielectric breakdown behaviour. All materials were based upon a single polymer, that is commonly used in high voltage applications, but with different additives. In all three of these systems, multiple melting transitions were observed, as a result of molecular fractionation effects during crystallization. In the virgin polymer, a space-filling banded spherulitic morphology was found to develop at low temperatures (102 °C and below) whereas, at higher temperatures, only a few isolated axialites were observed. Inclusion of the antioxidant resulted in greatly increased nucleation densities, such that, at low temperatures, no evidence of spherulitic organisation remained. At higher temperatures, sheaf-like lamellar aggregates developed, which were much smaller and much more numerous than in the case of the virgin polymer. Further addition of dicumyl peroxide (DCP) resulted in the rapid formation of a crosslinked network at 200 °C. Some crosslinking also occurred at 150 °C, but over a much longer timescale. Where extensive crosslinking occurred prior to crystallization, the resulting gel inhibited structural development, such that only a few small, isolated sheaves were able to form at 102 °C. In view of the principal application area of this material, the breakdown strength of each of the above systems was then measured and the whole data set was analysed statistically. When structural factors were considered alongside the statistics, no clear trends emerged to indicate that either the compositional or morphological variations were reflected in the short-term electrical failure processes.     

Role of Bulk Vaporization in the Dynamics of Laser-Induced Erosion Plumes of Metals

In different regimes of exposure of metals to pulsed laser radiation, we show the role played by the liquid-drop phase formed from the target material in a laser-induced erosion plume due to bulk vaporization, in the dynamics of this plume. For some metals, the ranges of power densities of the acting laser radiation, at which the condensed-phase particles influence the passage of laser radiation to the target surface, have been determined experimentally. The mechanism of realization of a low-threshold breakdown has been revealed.     

0.18μm CMOS工艺栅极氧化膜可靠性的衬底和工艺依存性

用斜坡电压法(Voltage Ramp, V-ramp)评价了0.18μm双栅极 CMOS工艺栅极氧化膜击穿电量(Charge to Breakdown, Q_bd)和击穿电压(Voltage to Breakdown, V_bd). 研究结果表明，低压器件(1.8V)的栅极氧化膜(薄氧)p型衬底MOS电容和N型衬底电容的击穿电量值相差较小，而高压器件(3.3V)栅极氧化膜(厚氧)p衬底MOS电容和n衬底MOS电容的击穿电量值相差较大，击穿电压测试值也发现与击穿电量 关键词： 薄氧 可靠性 击穿电压 击穿电量     

Laser-induced breakdown of soda-lime glass microspheres using Nd:YAG laser

The Nd:YAG laser-induced breakdown of 20 μm glass microspheres was investigated using time-resolved optical shadow and Schlieren images. Time-resolved imaging showed the location of the initial breakdown and the shockwave motion over its first 400 μm of expansion. Measured shockwave velocities were in the range of 1–10 km/s and showed a linear dependency on laser fluence within 30 ns.     

Hydrogen analysis in solid samples by utilizing He metastable atoms induced by TEA CO2 laser plasma in He gas at 1 atm

A TEA CO₂ laser (350 mJ–1.5 J, 10.6 μm, 200 ns, 10 Hz) was focused onto a metal sub-target under He as host gas at 1 atmospheric pressure with a small amount of impurity gas, such as water and ethanol vapors. It was found that the TEA CO₂ laser with the help of the metal sub-target is favorable for generating a strong, large volume helium gas breakdown plasma at 1 atmospheric pressure, in which the helium metastable-excited state was then produced overwhelmingly. While the metal sub-target itself was never ablated. The helium metastable-excited state produced after the strong helium gas breakdown plasma was considered to play an important role in exciting the atoms. This was confirmed by the specific characteristics of the detected H emission, namely the strong intensity with low background, narrow spectral width, and the long lifetime. This technique can be used for gas and solid samples analysis. For nonmetal solid analysis, a metal mesh was introduced in front of the nonmetal sample surface to help initiation of the helium gas breakdown plasma. For metal sample, analysis can be carried out by combining the TEA CO₂ laser and an Nd–YAG laser where the Nd–YAG laser is used to ablate the metal sample. The ablated atoms from the metal sample are then sent into the region of helium gas breakdown plasma induced by the TEA CO₂ laser to be excited through the helium metastable-excited state. This technique can be extended to the analysis of other elements, not limited only to hydrogen, such as halogens.     

Diffusion in Lorentz lattice gas automata with backscattering

The probability of first return to the initial intervalx and the diffusion tensorD _x are calculated exactly for a ballistic Lorentz gas on a Bethe lattice or Cayley tree. It consists of a moving particle and a fixed array of scatterers, located at the nodes, and the lengths of the intervals between scatterers are determined by a geometric distribution. The same values forx andD _x apply also to a regular space lattice with a fraction of sites occupied by a scatterer in the limit of a small concentration of scatterers. If backscattering occurs, the results are very different from the Boltzmann approximation. The theory is applied to different types of lattices and different types of scatterers having rotational or mirror symmetries.     

Using Toad Oocytes as an Ultrasensitive System for Estimating the Biological Activity of Trichosanthin

A sensitive bioassay for estimating the activity of Trichosanthin was developed by using intraoocyte microinjection as the technique and germinal vescicle breakdown as a marker. The GVBD inhibitory activity assay was million-fold more sensitive than the routinely used abortifacient activity assay. The detectable amount of Trichosanthin ranged from 0.5 to 100 pg. Since the least detectable dose was 0.5 pg, it made the assay suitable to analyse the microquantity of pure Trichosanthin used for studying the structure and function of the drug.     

Surface recombination in breakdown time delay experiments: Effect of different cathode materials

The late afterglow in nitrogen with iron electrode is studied by the breakdown time delay method, i.e., by measuring the breakdown time delay t_d as a function of the afterglow time . It is proposed that the cause of the secondary electrons initiating the breakdown is the energy of the surface recombination of nitrogen atoms on the iron electrode. The gas-phase and macrokinetic diffusive models are used to describe the experimental breakdown time delay data. By fitting the theoretical curve to the experimental data: (1) it has been confirmed that the recombination on the molybdenum glass is of the second order and the value of the surface recombination coefficient is determined at 4 mbar; (2) it has been shown that the surface recombination on the iron electrode is of the second order, and the effective recombination coefficients are determined; (3) the analytical form of the recombination coefficient as a function of the adsorption characteristics of surfaces and the pressure of the parent gas has been derived. In addition, the orders of surface recombination on the molybdenum-, aluminum-, and gold-plated electrode were determined by the same method.     

Analysis of powdered tungsten carbide hard-metal precursors and cemented compact tungsten carbides using laser-induced breakdown spectroscopy

Laser-induced breakdown spectroscopy (LIBS) has been applied to the direct analysis of powdered tungsten carbide hard-metal precursors and cemented tungsten carbides. The aim of this work was to examine the possibility of quantitative determination of the niobium, titanium, tantalum and cobalt. The investigated samples were in the form of pellets, pressed with and without binder (powdered silver) and in the form of cemented tungsten carbides. The pellets were prepared by pressing the powdered material in a hydraulic press. Cemented tungsten carbides were embedded in resin for easier manipulation.

Several lasers and detection systems were utilized. The Nd:YAG laser working at a basic wavelength of 1064 nm and fourth-harmonic frequency of 266 nm with a gated photomultiplier or ICCD detector HORIBA JY was used for the determination of niobium which was chosen as a model element. Different types of surrounding gases (air, He, Ar) were investigated for analysis. The ICCD detector DICAM PRO with Mechelle 7500 spectrometer with ArF laser (193 nm) and KrF laser (248 nm) were employed for the determination of niobium, titanium, tantalum and cobalt in samples under air atmosphere. Good calibration curves were obtained for Nb, Ti, and Ta (coefficients of determination r² > 0.96). Acceptable calibration curves were acquired for the determination of cobalt (coefficient of determination r² = 0.7994) but only for the cemented samples. In the case of powdered carbide precursors, the calibration for cobalt was found to be problematic.